RCA Home Theater System RTD317W User Guide

FCC Information  
FCC Information  
Important Information  
This device complies with part 15 of the FCC  
Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any  
interference received, including interference that  
may cause undesired operation.  
Ventilation  
THE LIGHTNING FLASH AND ARROWHEAD WITHIN  
THE TRIANGLE IS A WARNING SIGN ALERTING YOU  
OF “DANGEROUS VOLTAGEINSIDE THE PRODUCT.  
DVD copy protection  
Service information  
You must adequately ventilate the product. Make  
sure there is adequate space around the unit  
to provide proper air flow for ventilation. See  
diagram.  
This product should be serviced only by those  
specially trained in appropriate servicing  
techniques.  
In accordance with the DVD standard, your DVD  
player is equipped with a Copy Protection system,  
which can be switched on and off by the DVD  
disc itself, in order to make any recording of the  
relevant DVD disc onto a videotape of very poor  
picture quality, or even impossible. This product  
incorporates copyright protection technology  
that is protected by method claims of certain U.S.  
patents and other intellectual property rights  
owned by Macrovision Corporation and other  
rights owners. Use of this copyright protection  
technology must be authorized by Macrovision  
Corporation, and is intended for home use only  
unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly  
is prohibited.  
USER MANUAL  
RTD317W  
THE EXCLAMATION POINT WITHIN THE TRIANGLE  
IS A WARNING SIGN ALERTINGYOU OF IMPORTANT  
INSTRUCTIONS ACCOMPANYING THE PRODUCT.  
Important battery information  
7 cm  
Do not mix different types of batteries or new  
and old batteries. Do not use rechargeable  
batteries.  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses  
and can radiate radio frequency energy and, if  
not installed and used in accordance with the  
instructions, may cause harmful interference to  
radio communications.  
10 cm  
10 cm  
10 cm  
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSER-  
VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
In order to avoid any risk of explosion, observe  
the polarities indicated inside the battery  
compartment. Replace only with the type of  
batteries specified. Do not dispose of them in  
a fire or recharge them.  
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN  
THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.  
7 cm  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE  
SAME OR EQUIVALENT TYPE.  
If you are not using the remote control for a  
long period of time, remove the batteries.  
This product complies with DHHS Rules 21  
CFR Subchapter J. Applicable at the date of  
manufacture.  
WARNING: MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD REMAIN READILY OPERABLE  
DURING INTENDED USE. IN ORDER TO DISCONNECT THE APPARATUS FROM MAINS COMPLETELY, THE  
MAINS PLUG SHOULD BE DISCONNECTED FROM THE MAINS SOCKET OUTLET COMPLETELY.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference  
to radio or television reception, which can be  
determined by turning the equipment off and  
on, the user is encouraged to try to correct the  
interference by one or more of the following  
measures:  
Important Safety Instructions  
For your safety  
Please respect the environment and  
Caution  
The AC power plug is polarized  
(one blade is wider than the  
other) and only fits into AC  
power outlets one way. If the  
plug won’t go into the outlet  
completely, turn the plug over  
and try to insert it the other way.  
prevailing regulations. Before you  
dispose of batteries or accumulators,  
ask your dealer whether they are  
subject to special recycling and if  
they will accept them for disposal.  
This product utilizes a laser. Use of controls or  
adjustments or performance of procedures other  
than those specified may result in hazardous  
radiation exposure. Do not open covers and do  
not repair yourself. Refer servicing to qualified  
persionnel.  
Please read and save for future reference.  
Some of the following information may not apply  
to your particular product; however, as with any  
electronic product, precautions should be observed  
during handling and use.  
Protect the power cord from being walked on  
or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from  
the apparatus.  
Only use attachments / accessories specified by  
the manufacturer.  
Use only with a cart, stand, tripod,  
Reorient or relocate the receiving antenna.  
Increase the separation between the  
equipment and receiver.  
Read these instructions.  
Visible and invisible laser radiation when open  
and interlocks defeated.  
DO NOT STARE INTO BEAM.  
Keep these instructions.  
Connect the equipment into an outlet on a  
circuit different from that to which the receiver  
is connected.  
Consult the dealer or an experienced radio /  
TV technician for help.  
This class B digital apparatus complies  
with Canadian ICES-003.  
Cet appareil numérique de la class B  
est conforme à la norme du NMB-003  
du Canada.  
bracket, or table specified by the  
manufacturer, or sold with the  
apparatus. When a cart is used,  
use caution when moving the  
cart / apparatus combination to  
avoid injury from tip-over.  
Unplug this apparatus during lightning storms  
or when unused for long periods of time.  
Refer all ser vicing to qualified ser vice  
personnel. Servicing is required when the  
apparatus has been damaged in any way, such  
as the power cord or plug is damaged, liquid  
has been spilled or objects have fallen into the  
apparatus, the apparatus has been exposed to  
rain or moisture, does not operate normally, or  
has been dropped.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with a dry cloth.  
]
If it still won’t fit, contact a qualified electrician to  
change the outlet, or use a different one. Do not  
attempt to bypass this safety feature.  
Class 1 laser product  
Portable Cart  
Warning  
Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
Do not install near any heat sources such  
as radiators, heat registers, stoves, or other  
apparatus (Including amplifiers) that produce  
heat.  
Do not defeat the safety purpose of the polarized  
or grounding-type plug. A polarized plug has  
two blades with one wider than the other. A  
grounding type plug has two blades and a third  
grounding prong. The wide blade or the third  
prong is provided for your safety. If the provided  
plug does not fit into your wall outlet, consult  
an electrician for replacement of the obsolete  
outlet.  
Removing the power plug is the only way to  
completelyremovepowerfromyourproduct. Make  
sure the power plug remains easily accessible.  
WARNING: Changes or modifications to this unit  
not expressly approved by the party responsible  
for compliance could void the user's authority to  
operate the equipment.  
WARNING  
To reduce the risk of fire or electric shock  
hazard, do not expose this product to rain or  
moisture. The apparatus shall not be exposed  
to dripping or splashing and that no objects  
filled with liquids, such as vases, should be  
placed on the apparatus.  
Note  
Illustrations contained in this document are for  
representation only.  
This DVD player is designed and manufactured to  
respond to the Region Management Information.  
If the Region number of a DVD disc does not  
correspond to the Region number of this DVD  
player, this player cannot play the disc. The Region  
number for this DVD player is Region 1.  
This Home Theater has earned  
the ENERGY STAR.  
It's important to read this instruction prior to using your new product for the first time.  
- 1 -  
- 2 -  
- 3 -  
Connections and Setup  
Connections and Setup  
Connections and Setup  
Important Safety Instructions  
Digital optical input  
Additional safety information  
Where the mains plug or an appliance coupler  
is used as a disconnect device, the disconnect  
device shall remain readily operable.  
Otherimportantuseandcleaninginformationat  
the end of the booklet.  
Method 2  
Connecting to your TV (via HDMI input)  
Connecting the speakers  
Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each speaker to  
the corresponding color terminal at the back of the unit. Press down the tab to open the terminal and insert the  
wire. Release the tab to lock wire in the terminal.  
When connecting the speakers, make sure the polarities (“+speaker wire to+on the receiver. For example, red  
wire to red terminal on the receiver) of speaker wires and terminals match. If the cords are reversed, the sound  
will be distorted. Do not let the speaker wires touch each other, it will damage the Home Theater’s amplifier.  
Center speaker provided with this unit are magnetically shielded to protect your TV set. It is not recommended  
to place the front speakers, surround speakers and subwoofer near the TV set.  
1. Connect components capable of outputting  
Dolby Digital (e.g. TV or Set Top Box) or standard  
PCM (CD) format digital signals.  
Component video jacks (Pr, Pb, Y)  
Apparatus shall not be exposed to dripping or  
splashing and no objects filled with liquids, such as  
vases, shall be placed on the apparatus.  
Always leave sufficient space around the product for  
ventilation. Do not place product in or on a bed, rug,  
in a bookcase or cabinet that may prevent air flow  
through vent openings.  
Do not place lighted candles, cigarettes, cigars, etc.  
on the product.  
Connect power cord only to AC power source as  
marked on the product.  
Care should be taken so that objects do not fall into  
the product.  
Do not attempt to disassemble the cabinet. This  
product does not contain customer serviceable  
components.  
If your product operates on batteries, adhere to the  
following precautions:  
HDMI stands for High Definition Multimedia  
Interface. HDMI transfers digital audio and  
uncompressed digital video on a single cable.  
Press the HDMI button on the remote control to  
change output signals as follows: 480p, 720p,1080i  
and 1080p.  
The component video jacks are color-coded  
green, blue and red.  
Additional component video cables (not  
supplied) are required to provide best picture  
quality.They are usually color-coded green, blue  
and red.  
A. Any battery may leak electrolyte if mixed with a  
different battery type, if inserted incorrectly, or if all  
batteries are not replaced at the same time.  
B. Anybatterymayleakelectrolyteorexplodeifdisposed  
of in fire or an attempt is made to charge a battery  
not intended to be recharged.  
C. Discardleakybatteriesimmediately.Leakingbatteries  
can cause skin burns or other personal injury. When  
discarding batteries, be sure to dispose of them in the  
propermanner,accordingtoyourstate/provincialand  
local regulations.  
2. Push the OPTICAL button on the remote control  
to activate the sound from the external source.  
3. Push the SURROUND button on the remote  
control to select the sound mode.  
Connecting the antennas  
Connect the component video OUT jacks on the  
receivertothecomponentvideoINjacksonyour  
TV so the video content goes from the receiver  
to the screen.  
Ω
FM75  
Front Speakers  
White  
Cente Speaker  
Left  
Antenna  
Right  
To HDMI  
input  
HDMI cable  
Green/Gray  
D. Battery shall not be exposed to excessive heat such  
as sunshine, fire or the like.  
GND  
Y
(not supplied)  
P
B
Red/Gray  
White/Gray  
The AM and FM antennas connect to the AM and  
FM terminals on the system’s back panel.They must  
be hooked up in order to receive clear reception.  
Purple/Gray  
P
R
SPeAkeRS  
SR  
SL SUB CeN FR FL  
4Ω  
3Ω  
4Ω  
4Ω  
Connections and Setup  
Insert  
Green  
AM Loop Antenna  
Accessories provided  
Press  
1. Uncoil the AM Antenna wire.  
Subwoofer  
Blue  
Red  
Rear of the unit  
Rear of the unit  
2. Press down on the Antennas tab to open the  
terminal.  
Gray  
Blue/Gray  
Note: Refer to the owner’s manual of the connected  
TV as well.  
3. MakesurethewhitewireontheAMloopantenna  
isinsertedintotheAMloopterminalandtheother  
wire is inserted into the ground loop terminal.  
Using AUDIO IN jack  
Rear Speakers  
(Surround Sound)  
Connect the Ø3.5mm AUDIO IN jack on the front  
panel of the unit to the headphone output on mp3  
players.  
Release  
Rear of the unit  
Getting sound from external sources  
such as TV  
Using AUX IN jacks  
1. Connect the AUX IN jacks from the unit to the  
AUDIO OUT jacks on VCR, TV, Set Top Box or  
other component.  
2. Push the AUDIO/AUX button on the remote  
control to activate the sound from the external  
source.  
3. Push the SURROUND button on the remote  
control to select the sound mode.  
+
+
-
-
Right  
Left  
Connecting to your TV (VIDEO)  
Notes  
Method 1  
Composite video jack (yellow)  
To adjust each speaker volume level for optimum listening experience.  
(1) Press the LEVEL button on the remote control to select FL (front Left speaker).  
(2) Press the VOL+/VOL- buttons to adjust the value up or down (between -10dB and +10dB).  
(3) Repeat step (1) and (2) for the other speakers FR, SL, SR, CT, SW.  
Remote control and 2  
AAA batteries  
Left and right  
front speakers  
Center speaker  
Subwoofer  
Left and right  
Surround  
Speakers  
Ø3.5mm to Ø3.5mm audio cables (not  
included).  
If your television is a high definition  
television, use the unit’s progressive  
scanoutputtogetthehighestpossiblevideo  
resolution. Set the Progressive Scan option  
in the Video menu to On.  
Ifoneofthedevicesisnotworking,checkthat  
all the cables have been inserted properly  
into the jacks.  
Connecting mono components to your  
receiver: If your component has only one  
output for audio (mono), connect it to the  
white audio jack on the receiver and don’t  
use the cable’s red plugs.  
The basic video jack is color-coded yellow.  
Videocable(yellow)issuppliedfortheconnection  
for good picture quality.  
Connect the video OUT jack on the receiver to  
theVideo IN jack on yourTV so the video content  
goes from the receiver to the screen.  
Press either SOURCE on the main unit or AUDIO  
/AUX on the remote control to select AUDIO IN  
mode.  
Speaker gains may be set to levels of up to +10dB, actual max levels may also depend on your Volume Setting.  
Press the SURROUND button on the remote  
control to select the sound mode.  
One Pig-Tail  
antenna wire  
1. Left, Right (Front Speakers)  
Composite  
Video Cable  
Positioning speakers  
Front speakers carry primarily music and sound  
One external AM  
loop antenna  
3
effects.  
2. Center  
1
Things to consider before you connect  
Suggest using Ø3.5mm AUDIO  
IN jack for MP3 player and AUX  
IN jacks for auxiliary equipment  
such as DVD, VCR or PC.  
If the AUX IN (or AUDIO IN) audio signal  
is mono, you may not receive audio on  
all speakers.  
In surround mode, the center speaker carries most  
of the dialog as well as music and effects.  
It should be set between the left and right peakers.  
Thehumidityoftheroomshouldnotexceed75%.  
Ifyouhavetousetheunitoutdoors,donotexpose  
ittorainorsplashingwater.Theapparatusshould  
not be exposed to dripping or splashing and no  
objects filled with liquids, such as vases, should  
be placed on the apparatus.  
Moving the unit from a cold place to a warm one  
can cause condensation on some components  
inside the unit. Let the condensation disappear  
on its own before turning the unit on again.  
Before moving the unit, make sure the disc tray  
is empty.  
Ensure that the mains supply in your house  
complieswiththatindicatedontheidentification  
sticker located on the back of your unit.  
Install your unit horizontally, away from  
any source of heat (fireplace) or appliances  
creating strong magnetic or electric fields. The  
components of this unit are sensitive to heat.  
The maximum ambient temperature should not  
exceed 35°C / 95°F.  
2
3. Surround (Rear Speakers)  
The surround speakers’ overall sound balance  
should be as close as possible to the front peakers.  
Proper placement is vital to establish an evenly  
distributed sound field.  
1
4. Subwoofer  
3
Courtesy Dolby Laboratories  
4
Leave enough space around the unit to allow  
adequate ventilation: 10 cm/4 inches on either  
side and above the top, and 5 cm/2 inches at the  
rear.  
A subwoofer is designed to reproduce powerful low  
bass effects (explosions, the rumble of spaceships,  
etc.).  
Rear of the unit  
Rear of the unit  
- 4 -  
- 5 -  
- 6 -  
- 7 -  
Overview of Controls  
Playing Discs - Basic Functions  
Basic Playback Operations  
Connections and Setup  
Overview of Controls  
Aiming  
ON•OFF:  
DVD:  
TUNER:  
Turns on/off the unit.  
Selects the DVD mode.  
Selects the TUNER and selects between FM/  
AM.  
SURROUND: Changes the Surround sound  
setting.  
Using remote control to navigate through  
the on-screen menus  
Compatible discs  
• DVD, DVD-R, DVD-RW, DVD+R, DVD+RW  
• CD, CD-R, CD-RW  
Variable slow motion  
Front speaker placement  
For best results, follow the speaker placement  
below.  
Aim surround speakers straight across the room,  
not down at viewers, to help create a more open,  
spacious surround sound field.  
1. Press SLOW button on the remote in play  
mode.  
Press the button to select between  
5.1 Channel and Stereo modes.  
Use  
,
,
,
and OK on the remote control to  
2. Each time the SLOW button is pressed the  
speed of slow-motion playback changes in the  
following sequence:  
navigate through the on-screen displays (the  
DVD player’s menu, the Info Display that appears  
during playback, or a disc’s menu).  
Compatible formats  
• DVD, JPEG  
• CD, VCD  
Alignment  
AUDIO/AUX: Selects and toggles between the front  
AUDIO IN mode and rear AUX IN mode. (for  
listening to audio input from connected TV,  
VCR or SetTop BOX).  
Align the center speaker evenly with (A) or slightly  
behind (B) (the left and right speakers), but not  
ahead of them.  
Remote control functions in tuner mode  
TUNER:  
Selects theTUNER and switch between  
SF 1/ 2  
SF 1/ 3  
SF 1/ 4  
SF 1/ 5  
Use  
,
,
,
on the remote to move through on-  
FM/AM.  
screen menus in the direction of the arrow button  
(e.g., to move right, press ). The arrow buttons are  
used to highlight an option. Once highlighted,  
press OK to select the option that is highlighted.  
Regional coding  
PLAY  
SF 1/ 7  
SF 1/ 6  
OPTICAL:  
Selects OPTICAL IN at rear for digital audio  
connection.  
Number entry.  
Quits the current setting manually from the  
TV screen without saving change.  
Accesses the Info menu.  
VOL+/–:  
MUTE:  
Adjusts the sound volume.  
Mutes and restores the sound.  
Your unit has been designed to process regional  
management information stored on DVD discs. The  
regional code for your unit is 1. Discs that have a  
different regional code will not play.  
3. Press PLAY to resume normal playback.  
0-9:  
CLEAR:  
TUNER +/–: Tunes down and up the radio  
frequencies.  
MEMORY: Stores a station.  
Changing chapter/track  
While the disc is playing, press the CH+/- button  
to go immediately to the next or previous chapter,  
or to the next or previous track.  
Alternative Surround Placement  
Rear wall  
Operating the DVD receiver  
1. Turn on your television set.  
2. Press ONOFF on the remote or ON/STANDBY  
located on the unit’s front panel. Press DVD on  
the remote control.  
INFO:  
TITLE:  
CH+/–:  
AUDIO:  
Selects programmed stations.  
Selects between Stereo and Mono  
mode for Tuner (FM).  
If rear wall mounting is the only choice, aim the  
speakers at each other (A), towards the front (B) or  
towards the sidewalls (C, D).  
Accesses the title menu of DVD discs.  
Note:  
Zoom  
DISC MENU: Accesses the disc menu during playback.  
1. While a disc is playing, press ZOOM until you  
reach the zoom size you want. The ZOOM  
button toggles through 2x, 3x, 4x and then  
zooms out to 1/2x, 1/3x and 1/4x, then returns  
to normal playback.  
Insert 2“AAA”(“UM-4”/”R03”) batteries  
to the remote control prior to use.  
OK:  
/
Confirms your selection.  
Experiment with placement until sounds seem to  
surround you, rather than come from behind you.  
/
/
:
To navigate through the menus. The left and  
right arrows also tune the radio frequency in  
the tuner mode.  
Mutes and restores the sound.  
Enters Setup menu.  
Loading disc  
No adjacent walls  
Angle  
Surround speakers can go on stands facing each  
other to approximate sidewall mounting (A), or to  
thesidesorrearoftheviewingarea, aimedupwards;  
they can go right on the floor, or preferably, a few  
feet off the floor such as on end tables (B).  
1. Press on the front panel to open the disc tray.  
2. Place a disc onto the disc tray with the label side  
up.  
MUTE:  
SETUP:  
RETURN:  
VOL +/- :  
Place the left and right speakers to form a 45-  
degree angle with your favorite viewing position  
to duplicate the soundtrack mixer’s perspective.  
2. Move from one area to another (pan) using the  
arrow buttons.  
3. To turn ZOOM off, press ZOOM until you get to  
the ZOOM OFF option.  
In DVD mode, returns to the previous menu.  
Adjusts the sound volume.  
3. Press again to close the disc tray.  
Height  
CH+/ , CH–/ : Directly accesses the next or previous  
chapter (DVD) or track (CD). Selects  
Playback  
The three front speakers should be as close as  
possible to the same height. This often requires  
placing the center speaker directly on top (A) or  
beneath (B) the TV set.  
Overview of Controls - Front Panel Controls  
Types of menus  
Switch the unit and the TV set on.  
Disc menu — The appearance and contents of  
this menu varies according to the type of disc  
you have inserted. It is separate from the Setup  
menu.  
Info menu — The unit’s Info menu appears at  
the top of the screen while the disc is playing.  
Press INFO on the remote to switch the Info  
menu on or off.  
1. After loading  
a
disc, playback starts  
programmed stations in TUNER mode.  
Starts reverse accelerated play.  
Starts playing a disc.  
Starts forward accelerated play.  
Selects SLOW motion function.  
Stops playback.  
Freezes frame, accesses frame advance.  
Accesses the audio function.  
Accesses the camera angle function for DVD  
disc.  
Accesses the Zoom function.  
Selects the subtitle languages or turns  
subtitle off ( if available).  
Changes video output signals (480p, 720p,  
1080i or1080p).  
automatically, or the disc menu appears. If the  
disc menu appears, select the Play option to  
begin playback.  
REV:  
PLAY:  
FWD:  
SLOW:  
STOP:  
PAUSE:  
AUDIO:  
ANGLE:  
Toggles between different  
Switches the  
subwoofer output levels (among Starts/pauses  
Adjusts the unit on and  
playing a disc.  
soft/balance/strong/powerful).  
2. Press STOP to stop playback.  
volume.  
off.  
A
Accelerated play  
While the disc is playing, press REV or FWD one  
or more times to vary the speed and direction of  
the accelerated play. Press PLAY to resume normal  
playback.  
TT  
CH  
Test tone/Channel balance  
Channel balance  
Setup menu — Press SETUP to access this  
menu.  
Your receiver is equipped with  
a
test signal  
B
ZOOM:  
SUBTITLE:  
generator for balancing the channels. As the signal  
“travels” from channel to channel, adjust the level  
controls until each channel plays at the same  
loudness level.  
Pause  
While the disc is playing, press PAUSE once for freeze  
frame. Press PLAY to resume normal playback.  
Selects the input sources. Press  
repeatedly to select:  
Stops disc  
playback.  
AUDIO IN jack -  
connects audio  
devices.  
Opens and closes  
the disc tray.  
HDMI:  
• DVD – to watch DVD videos.  
• TUNER – to listen to the radio.  
• AUX IN (rear) / AUDIO IN(front)  
- to listen to the audio input  
from the connected TV, VCR or  
Set Top Box.  
Better surround placement  
Location  
If possible, place surround speakers to either side  
of the listening area, not behind it.  
Level adjustment and surround channel level  
expectation  
Frame advance  
SUBWOOFER: Selects among subwoofer output levels  
1. Press PAUSE twice. “Stepis displayed.  
2. Each time you press PAUSE button, the picture  
advances one frame.  
Even though you adjust the surround channel  
to be as loud as the others on the test signal, on  
actual program material the surround channel is  
adjust the surround level; program producers use  
surround for subtle atmospherics and ambience,  
and only rarely for special effects.  
(soft/balance/strong/powerful).  
Turns on/off random playback on CDDA disc.  
Accesses the repeat function.  
Toggles channels for different level settings.  
Adjusts the value using VOL +/-.  
RANDOM:  
REPEAT:  
LEVEL:  
3. Press PLAY to resume normal playback.  
Height  
• OPTICAL (rear) - to connect  
digital audio components.  
If space permits, install surround speakers 2-3 feet  
above viewers. This helps to minimize localization  
effects.  
- 8 -  
- 9 -  
- 10 -  
- 11 -  
 

Radio Shack Portable Speaker 40 1437 User Guide
RCA Flat Panel Television RLED1530 User Guide
Rowenta Styling Iron Pressure iron steamer User Guide
RuggedCom Computer Hardware RX1501 User Guide
Ryobi Blower RY09550 User Guide
Ryobi Saw BS901 User Guide
Samsung All in One Printer CLX 318X User Guide
SanDisk Cell Phone Accessories miniSDHC User Guide
Sanyo Cordless Telephone CLT D6720 User Guide
Sears Saw 113298141 User Guide